Tricon Copper from Tricon Piping Systems Inc.

 

For Applications Up To 250 degree Farenheit Below And Above Ground

• Chilled Water
• Condensate
• Condenser Water
• Domestic Hot Water
• Heating Hot Water
• Potable Water
• Process Piping

Service Pipe:

The service pipe shall be Type “K”, or Type “L” hard drawn seamless copper tubing to ASTM B-88 and WWT-799.

Refrigerant piping shall meet ASTM B-280, Type ACR and ASME 31.5 Straight lengths of piping will be supplied in 20 ft. lengths with 6” of piping exposed at each end for field joint fabrication.

Insulation:

The insulation shall be a foamed in place closed cell polyurethane which completely fills the annular space between the carrier pipe and the exterior casing. The insulation shall have the following physical properties:
Minimum Density (lb./cu. ft.) 2.0 (ASTM D-1621)
90-95 % Closed Cell (ASTM D-2856)
“K” Factor BTU/Hr. sq. ft. °F/in. 147 (ASTM C-177)

Exterior Casing:*

The exterior casing shall be:

1. Seamless, extruded white PVC Type 1, Grade 1, Class 12454-B per ASTM D-1784 or
2. High Density Polyethylene (H.D.P.E.) with the following physical properties:
   • ASTM D-3350…Resin Type III, Grade P34
   • ASTM D-633…Ultimate Elongation 850%
   • ASTM D-633…Tensile Yield Strength 3300 psi
   • ASTM D-790…Tangent Flexural Modules 175,000 psi

No polyethylene tape casings will be allowed.

Sub-Assemblies:

All fittings, anchors, end seals, other sub-assemblies shall be prefabricated or field fabricated dependant upon engineer’s option and/or site conditions.

Field Joints:

After soldering and hydrostatic testing, PVC jacketed straight field joints shall be insulated with polyurethane foam to the thickness specified, PVC sleeve and pressure sensitive tape. HDPE jackets will use polyurethane foam and a heat shrinkable sleeve.

Expansion/Contraction Compensation:

Expansion and contraction within the piping system shall be accommodated with factory prefabricated internal expansion elbows, z-bends, expansion loops, and anchors specifically designed for each application. External expansion compensation can be provided with the use of flexible foam bolsters.

Download the Tricon Copper Specification Sheet

#preinsulatedpipes #pipes #heating #cooling

For other relevant searches, you might want to try:

(22 07 16) Plumbing Equipment Insulation (22 10 00) Plumbing Piping (22 15 00) General Service Compressed-Air Systems (23 07 19) HVAC Piping Insulation (23 11 13) Facility Fuel-Oil Piping (33 51 13) Natural-Gas Piping (33 52 00) Liquid Fuel Distribution (33 52 13) Fuel-Oil Distribution (33 52 13.13) Fuel-Oil Piping (33 52 13.23) Fuel-Oil Pumps (33 52 16) Gasoline Distribution

(33 52 16.13) Gasoline Piping (33 52 19) Diesel Fuel Distribution (33 52 19.13) Diesel Fuel Piping (33 52 43) Aviation Fuel Distribution (33 52 43.13) Aviation Fuel Piping (33 61 00) Hydronic Energy Distribution (33 61 13) Underground Hydronic Energy Distribution (33 61 23) Aboveground Hydronic Energy Distribution (33 63 00) Steam Energy Distribution (33 63 13) Underground Steam and Condensate Distribution Piping (33 63 23) Aboveground Steam and Condensate Distribution Piping