Scale/6 Decorative Accents Section 08350. CSI 3-Part Specifications.

PRODUCT SPECIFICATIONS:  SECTIONS 08350 - FOLDING DOORS

PART I GENERAL

(See Project Guide Specifications for Scope, Related Work, References, Submittals, Product Delivery and Acceptable Manufacturers paragraphs,)

PART 2 PRODUCTS

2.1 FOLDING DOORS shall be manually operated wood, folding type as manufactured by Panelfold, Inc., Miami, Florida, U.S.A. and installed by an authorized representative of the manufacturer in openings prepared by others to SCALE/6 Decorative Accents requirements.

2.2 TRACK AND HANGERS: Track shall be extruded aluminum. Hanger assemblies with two ballbearing wheels shall be suspended on alternate panels. A four-wheel truck hanger assembly shall be installed on each end post.

2.3 DECORATIVE ACCENTS shall be (specify: open woven cane inserts; closed woven cane inserts; clear cracked ice translucent inserts; amber cracked ice translucent inserts; clear transparent inserts, or carved (one or both sides) panels).

2.4 PANEL SURFACES: Panels shall be specially laminated engineered wood core, bonded with water-resistant, plastic glue and surfaced with one of the following (colors to be selected from manufacturer's standards):

2.4.1 Woodtex wood grain vinyl, Class A flame spread.
2.4.2 Startex solid color vinyl, Class A flame spread,
2.4.3 Fabrictex fabric textured vinyl, Class A flame spread.
2.4.4 Ropetex rope textured vinyl, Class A flame spread.
2.4.5 Genuine wood veneer shall be (specify: clear lacquer finished; unfinished, sanded ready for field finishing by others; factory specially finished to match owner's submitted sample) species as specified: White Ash; Red Oak; Natural Birch, White Maple; or American Walnut.
2.4.6 High pressure plastic laminate, vertical grade.

2.5 CONNECTOR HINGES: Panels shall be hinged and edge sealed against sound light and air transmission with heavy duty, dual-wall, flame resistant, extruded vinyl, Hinges shall be securely locked into and protect the panel edges. They shall provide "Memory-Action" causing the panels to extend and stack equally, smoothly, and quietly. Color from manufacturer's selector.

2.6 TRIM: Doors shall be supplied with (specify: decorative track; optional plain track with track mould to conceal track, or optional plain track with extruded aluminum sub-channel for recessed track). A jamb mould for jamb closure shall be furnished.

2.7 HARDWARE: Handles, Touch-Bar automatic latches, all necessary screws, installation hardware and instructions shall be furnished. Security units shall be as specified: Privacy latch and emergency release, cylinder lock one side only; cylinder lock one side, privacy lock other, cylinder lock two sides. Optional. Master-keyed insert type cylinder with lazy cam and flat tail piece, by others, shall be installed in lieu of regularly furnished cylinder.

2.8 STACK FORMULA: Approximately 1-1/4"/ft. (105mm/m) plus 3" (76mm) for each end post assembly.

2.9 HANGING WEIGHT: Approximately 2.2 lbs./ft.2 (11 kg/m 2).

PART 3 EXECUTION

(See Project Specifications Guide for Execution, Inspection, Preparation, Installation, Cleaning and Demonstration paragraphs,)

NOTE: The ASTM  84 procedure Class A flame spread and other test results referenced herein are for comparison purposes only and are not intended to reflect hazards presented by this or any other materials under actual fire conditions.

Panelfold^®
FOLDING DOORS - ACOUSTICAL FOLDING PARTITIONS - OPERABLE WALLS - RELOCATABLE WALLS
Panelfold, Inc. PO Box 680130 Miami, Florida 33168
305/688-3501 - FAX: 305/688-0185
Panelfold is constantly developing its products and reserves the right to change specifications without notice. Copyright© 1998 by Panelfold, Inc. All rights reserved.