PrimeSpacer Series 300 Section 10615. CSI 3-Part Specifications.

PrimeSpacer SERIES 300
Self-Contained Panels Model 350
Factory Assembled Panels Model 360

PRODUCT SPECIFICATIONS:

SECTION 10615 - RELOCATABLE WALLS

PART 1 GENERAL

(See Project Guide Specifications for Scope, Related Work, References, Submittals, Product Delivery and Acceptable Manufacturers paragraphs)

PART 2 PRODUCTS

2.1 RELOCATABLE WALLS shall be manufactured by Panelfold, Inc., Miami, Florida, U.S.A. and installed by an authorized representative of the manufacturer in openings prepared by others to PrimeSpacer Series 300 requirements.

2.2 OPERATION shall consist of a series of floor supported portable panels.

2.3 PANEL CONFIGURATION shall be as follows for areas indicated on the plans:

2.3.1 MODEL 350 shall be comprised of a series of self-contained panels with top spring-bias mechanisms which engage the panels against the ceiling,
2.3.2 MODEL 360 shall be comprised of a series of factory-assembled panels which are retained at the ceiling by continuous splines.

2.4 PANELS shall be 3" (76) thick and nominally 49" (1245) wide. Panel faces shall be laminated to metal frames. Panels shall have appropriate internal insulation to achieve specified STC. The tops of the panels shall be reinforced to support suspension components. The vertical edges of the panels shall not require trim thus minimizing the appearance of the vertical joining of the Sheer-Look  panels.

2.5 PANELS shall be factory surfaced with one of the following (colors to be selected from manufacturer's standards):

2.5.1 Manufacturer's standard vinyl, Class A flame spread (specify: Type 1; or Type 11).
2.5.2 Manufacturer's standard Ribtex vertical-rib wall carpeting, Class A minimum weight 21 oz. per lineal yard, fused bonded backing.
2.5.3 Manufacturer's Woventex panel fabric, Class A, acrylic backed.
2.5.4 Maharam Tekwall 1000 panel fabric, Class A, acrylic backed.
2.5.5 Genuine unfinished wood veneer shall be (specify: White Ash, Red Oak, Natural Birch, American Walnut or other species as specified).
2.5.6 High pressure plastic laminate, vertical grade.
2.5.7 Customer's Own Material to be factory applied (subject to approval by the manufacturer for suitability to standard manufacturing processes and equipment).
2.5.8 Unsurfaced panel skins for field finishing by others.

2.6 HANGING WEIGHT of panels shall not exceed 6 lbs./ft2 (29.8Kg/m2).
2.7 ACOUSTICAL RATING of panels as tested by an independent acoustical laboratory in accordance with ASTM E90-85 test procedures shall be (specify: STC 42; or STC 38).
2.8 SOUND SEALS shall be as follows:

2.8.1 Vertical seals between panels shall consist of deep nesting, universal interlocking ESP bronze steel astragals incorporating continuous vinyl acoustical seals. Vertical astragal vinyl seals shall be installed on the outboard edges of the panel skins in a double row with an acoustical labyrinth.
2.8.2 Horizontal TOP seals shall be continuous contact extruded vinyl shapes.
2.8.3 Horizontal BOTTOM seals shall be continuous contact extruded vinyl shapes.

PART 3 EXECUTION

(See Project Specifications Guide for Execution, Installation, Cleaning and Demonstration paragraphs),
NOTE: The ASTM-84 procedure Class A flame spread and other test results referenced herein are for comparison purposes only and are not intended to reflect hazards presented by this or any other materials under actual fire conditions.

Panelfold^®
FOLDING DOORS - ACOUSTICAL FOLDING PARTITIONS - OPERABLE WALLS - RELOCATABLE WALLS
Panelfold, Inc. PO Box 680130 Miami, Florida 33168
305/688-3501 - FAX: 305/688-0185
Panelfold is constantly developing its products and reserves the right to change specifications without notice. Copyright© 1998 by Panelfold, Inc. All rights reserved.