Excel 10 Q7750A Zone Manager. CSI 3-Part Specifications. Large file (>500kB).

The Q7750A Excel 10 Zone Manager is a programmable master controller for an Excel 10 Subsystem. It provides energy management functions and communication interfaces between EXCEL 5000^� System products and the Excel 10 Echelon^� LonWorks^� (E-Bus) network. The Q7750A provides C-Bus (9600 baud and 1M baud) and E-Bus (78k baud) communication interfaces. It also maps user selectable Excel 10 Subsystem data points into C-Bus points with a full set of point attributes, including user addresses.

There are two hardware versions of the Q7750A. 1000-series devices (with a part number suffix of 1xxx) have a twisted pair topology (TPT) E-Bus transceiver. 2000-series devices (with a part number suffix of 2xxx) have have a free topology (FTT) E-Bus tranceiver.

The Q7750A is delivered with operating system software on EPROMs. The Zone Manager contains all time programs, user addresses and Excel 10 Subsystem mapping information. Mapping is the term used to describe the allocation of Excel 10 Subsystem data to Q7750A data points that are accessible from the C-Bus. This mapping process is executed using a PC-based software tool (CARE or E-Vision).

Category

Limits/Rates/Options

LED No.

Explanation

LED function if On

LED function if Off

The maximum number of nodes per E-Bus is 60. With the addition of a Q7751A Router, the maximum number of nodes increases to 120 or 60 per E-Bus segment.

The recommended wire for the E-Bus will level IV, 22 AWG (Belden part number 9D220150) or plenum rated Level IV, 22 AWG (Belden part number (H2201504) nonshielded, twisted pair, solid conductor wire. Honeywell E-Bus cable is available. See Installation Instructions, form number 95-7509.

Additionally, Echelon approved shielded cable can be used. Contact Echelon Corp. Technical Support for the recommended vendors of Echelon approved cables.

1000-series:
The TPT E-Bus is a daisy chain topology — the bus needs to go serially from one controller to another without branching.

2000-series:
An FTT network can accomodate bus, star, loop or any combination of these topologies. This simplifies system installation and makes it easy to add nodes should the network need to be expanded. 2000-series devices can be used to replace 1000-series devices using a TPT/FTT router. Maximum length of an FTT network is depedent on a number of factors, see E-Bus Wiring Practices, form 74-2865 for details.

C-Bus

The C-Bus transmits data between EXCEL 5000^� System Controllers, Devices and Building Supervisors at 9600 baud or 1M baud (921.6k baud).

Mechanical:
Dimensions in in. (mm) HWD:

9-11/16 x 7-9/16 x 2-19/32 (246 x 192 x 66).

Weight in lb (kg):

2.6 (1.2).

Housing Material:

ABS plastic.

Environmental Ratings:
Operating Temperature:

32� to 122�F (0� to 50�C).

Shipping Temperature:

–29.2� to 140�F (–34� to 60�C).

Relative Humidity:

5% to 90% noncondensing.

Approval Bodies:

The Q7750A1xxx is listed under UL 916, File Number S4804

(QVAX, PAZY) and is being listed by CSA. The Q7750A meets FCC part 15 class B requirements.

Protection Class: IP30.
Electromagnetic: EN 50081-1, EN 500 82-1.

� U.S. Registered Trademark
Copyright �1995 Honeywell Inc. - All Rights Reserved.

The maximum C-Bus network length is 3900 ft (1200m), but with the addition of an XD 509 Excel High Speed Repeater, the C-Bus can be extended (an additional 3900 ft (1200m) for each XD509).

The maximum number of controllers or devices per C-Bus is 29.

Memory:
The operating system EPROMs contain 768k bytes of space. There are also 240K bytes of RAM and 1K byte of EEPROM space available for software use.

Connections:
There are two connectors available on the Q7750A Excel 10 Zone Manager:

1. Connector 1; power, C-Bus and E-Bus network.

2. Connector 2; B-Port (RS-232) compatible with a PC for the XI 581 Operator Interface and, via XI 584, E-Vision, CARE, and LiveCARE.

Hardware:
The CPU is based on an INTEL 80C188XL Microprocessor and also uses an Echelon� 3120 Neuron Chip.

Power Supply:
24 Vac with a valid range (of 19.4 to 28.8 Vac) at 50/60 Hz.

Power Consumption:
6 VA maximum at both 50 and 60 Hz.

Battery Back-up:
The back-up battery, used for RAM and the Real Time Clock, is a 3-volt Lithium (type CR 1/2 AA, VARTA number 6127 or equivalent). The backup time for a new battery is 30 days with a minimum of 72 hours after the first battery empty (voltage falls below 2.5 volts) alarm is detected.

Mounting Options:
The Q7750A can be mounted in a ring cabinet or attached to 1-3/8 by 9/32 (35 by 7.5 mm) EN 50 022 DIN rail.

Accessories:
The following accessories are available:

Table 3. Accessories

Subject to change without notice.

74-2950-1   Rev. 1/97

Honeywell Europe S.A.
3 Avenue du Bourget
B-1140 Brussels
Belgium

Helping You Control Your World

Manufacturing location is certified to