Pivot Lock. CSI 3-Part Specifications.

PIVOT-LOCK DETAILS AND SPECIFICATIONS

1. SCOPE

1.1 Furnish a ___ x ___ size, Pivot-Lock building for interior use as manufactured by Porta-King Building Systems, St. Louis, Missouri, conforming to the following specifications. Building is shipped completely knocked down.

1.2 Related work not included in this section; electrical service supply and connection, foundation work offloading, and installation.

2. MATERIALS

2.1 WALL PANELS
Panels to be 3" thick, 8' high and 2' or 4', as specified, with expanded polystyrene board core (UL Class 1), and 1/8" vinyl-covered hardboard permanently laminated to both sides. Panels to have insulating factor of R-13.

2.1.1. Panels to be 1 3/4" thick with R-7 insulation.

2.1.2. Standard finishes: walnut, pecan, beige, white, gray, and blue.

2.2 STRUCTURAL FRAMEWORK
Anodized aluminum extrusions alloy 6063T6, to frame entire wall sections, permitting connection of one panel to another using the Pivot-Lock connection method. All framework to be factory installed, so wall panels are ready for installation without additional on-site labor.

2.3 PANEL ACCEPTORS
Aluminum extrusions for attachment to perimeter (or existing) walls, permitting wall sections to pivot and lock from acceptor.

2.4 BASE PLATE
Aluminum channel extrusion is shipped pre-cut and pre-mitered for ease of leveling, attachment to foundation and to provide a smooth surface for caulking and sealing.

2.5 CONCEALED ATTACHMENT BRACKETS
For fastening wall panel to the foundation on exterior applications or extremely long runs. Fasteners to be furnished by others.

2.6 ACOUSTICAL CEILING
Acoustical grid-type ceiling system to include hanger tabs, tie wire, and 2' x 4' white lay-in acoustical board (UL Class 1).

2.7 CEILING CAP
To be provided for installation on top of wall sections shipped pre-cut and pre-mitered, as required, to fit snugly around the top perimeter of wall sections. Ceiling cap to be aluminum extrusion sized to fit over wall sections and to include vertical fascia flange for neat, trim appearance as an integral part of the cap.

2.8 DOORS
Doors to be shipped pre-hung, installed in the wall sections with butt hinges and key-in-knob lockset shipped separate. Wall section to include door threshold.

2.8.1 Standard door to be a 3068 x 1 3/4" full flush, vinyl-clad walnut, hollow-core wood door.

2.9 WINDOWS
Windows (where specified) to be factory glazed with 3/16" clear tempered safety glass. Doors (where specified) to be factory glazed with 1/8" clear tempered safety glass. All glass to be shipped installed, so onsite glazing is not required.

2.10 ELECTRICAL WIREWAYS
Anodized aluminum extrusions to form tubular wireway which pivots and locks between wall sections, where required, for concealed electric. Switches and/or receptacles are shipped installed in the snap-on-cover, which provides easy access for initial wiring and additional future electric service. Wiring to be furnished and installed by others.

Note: Width of adjacent wall panel to be reduced to maintain standard 2' or 4' increments.

2.11 ROOF DECK
Roof deck to be 22 gauge (1 1/2" deep) for buildings 12' in width or less, or 18 gauge (1 1/2" deep) for wider buildings up to 16'; and to be roll-formed steel panels which interlock (not nestable) with one another to serve as a top cover for the building and support for a standard acoustical grid system.

Porta-King
4133 Shoreline Drive
Earth City, Missouri 63045
Toll Free: 800-284-5346
Phone: 314-291-4200
Fax: 314-291-2857
http://www.portaking.com