ASD027. CSI 3-Part Specifications.

FIRE LABELED SYSTEM 4 (LOW FORCE), SPECIFICATION

ASD027 May 1995

SPECIFIER NOTE:

THE FOLLOWING DATA IS INTENDED TO ASSIST IN SPECIFYING PEMKO

PRODUCTS. INCORPORATE IN A PROJECT SPECIFICATION WHERE

APPROPRIATE.

CAREFULLY REVIEW TO ENSURE COORDINATION WITH ALL CONTRACT

DOCUMENTS.

1. PRODUCT: PEMKO FIRE LABELED SYSTEM No, 4, PAIR OF DOORS WITH

LOW FORCE NYLON BRUSH

2. MANUFACTURER:

PEMKO * Ventura PEMKO * Memphis

4226 Transport Street 5535 Distribution Drive

Ventura, CA 93003 Memphis, TN 38141

Phone: (800) 283-9988 Phone (800) 824-3018

Fax: (800) 283-4050 Fax: (800) 243-3656

3. MATERIAL & FINISH:

SPECIFIER NOTE:

PRODUCT SELECTED IS AVAILABLE IN MATERIALS & FINISHES SPECIFIED

BELOW. WHERE MORE THAN ONE MATERIAL IS LISTED FOR A PRODUCT,

SELECT PARAGRAPH FOR MATERIAL YOU WANT.

EDIT BRACKETED TEXT TO SPECIFY FINISH. DELETE TEXT NOT DESIRED.

MATERIALS & FINISHES NOT LISTED MAY BE AVAILABLE BY SPECIAL

ORDER.

THRESHOLD: PEMKO No. 271A

Aluminum, Extruded

* Alloy Type 6063-T5

* Chemical and physical properties per the Aluminum

Association, Inc.

* Federal Specification QQ-A-200/9C.

* [271A, Mill Finish; 271D, Dark Bronze Anodized;

271G, Gold Anodized]

DOOR BOTTOM SWEEP: PEMKO No. 18062CP

HOUSING:

Aluminum, Extruded

* Alloy Type 6063-T5

* Chemical and physical properties per the Aluminum

Association, Inc.

* Federal Specification QQ-A-200/9C.

* [18062CP, Clear Anodized; 18062DP, Dark Bronze

Anodized; 18062GP, Gold Anodized]

BRUSH:

* Nylon, Type 6, heat stabilized

PERIMETER GASKETING: PEMKO No. 45061CP

HOUSING:

Aluminum, Extruded

* Alloy Type 6063-T5

* Chemical and physical properties per the Aluminum

Association, Inc.

* Federal Specification QQ-A-200/9C.

* [45061CP, Clear Anodized; 45061DP, Dark Bronze

Anodized; 45061GP, Gold Anodized]

BRUSH:

* Nylon, Type 6, heat stabilized.

MEETING STILES GASKETING: PEMKO No. 45041CP (2 each req'd)

HOUSING:

Aluminum, Extruded

* Alloy Type 6063-T5

* Chemical and physical properties per the Aluminum

Association, Inc.

* Federal Specification QQ-A-200/9C.

* [45041CP, Clear Anodized; 45041DP, Dark Bronze

Anodized; 45041GP, Gold Anodized]

BRUSH:

* Nylon, Type 6, heat stabilized.

4.TEST & CODE COMPLIANCE:

Fire Label: Classified By UL For Application To Swinging

Type Fire Doors of the Hollow Metal or Steel

Covered composite type Rated up to 3 Hours, or

Wood Core Fire Doors rated up to 1-1/2

Hours Listed and Labeled as Gasketing

Materials. Tested in accordance with UL10B

by Underwriters Laboratory, Inc. .

Smoke Label: Smoke tested by WYLE Laboratories in

with UL 1784-90; meets the

requirements of NFPA 105.

Handicapped: Threshold complies with CABO/ANSI A117.1-

1992; ADA 1990; ADAAG 1991 Guidelines

5.INSTALLATION:

Installation to be performed in strict accordance with

manufacturers instructions furnished with product.

Threshold: Carefully cope to fit within frame opening.

Fasten with flat head wood or machine screws provided and

appropriate anchors as required. Use sealant or compound at

all edges and joints.

Door Bottom: Cut to length equal to door width,crimp

ends of brush backing to retain bristles. Fasten to bottom

of door, locate screws in center of slots.

Adjust for proper contact with floor and tighten screws.

Perimeter Gasketing:Trim to length, crimp ends of brush

backing to retain bristles. Fasten to header first, then

jambs, ensure contact at threshold, hold lightly against

door and install screws in center of slots (drill metal

frame 7/64" or #36) Carefully miter or cope at corners

to ensure tight joints and continuous seal. Adjust as

required and tighten screws..

Meeting Stiles: Trim to length required, squeeze ends of

brush backing to retain bristles. Position on meeting stile

edges so that brush slightly overlaps, install screws in

center of slots. Adjust for optimum seal and door

operation, then tighten screws.

6 WARRANTY:

Guaranteed by manufacturer against defects in material or

workmanship for three years