American Specialties Inc.  

Toilet Accessories. CSI 3-Part Specifications.

SECTION 10810

TOILET ACCESSORIES

PART 1 GENERAL

1.1 SECTION INCLUDES
NOTE ** Delete items below not required for project.

    A. Toilet Room, Lavatory, and Shower Accessories.

    B. Hospital and Medical Service Accessories.

    C. Utility Room Accessories.

    D. Security/Detention Accessories.

1.2 RELATED SECTIONS
NOTE ** Delete any sections below not relevant to this project; add others as required.

    A. Section 04810 - Unit Masonry Assemblies.

    B. Section 09260 - Gypsum Board Assemblies.

    C. Section 09300 - Tile.

    D. Section 10160 - Metal Toilet Compartments.

    E. Section 10165 - Plastic Laminate Toilet Compartments.

    F. Section 10170 - Plastic Toilet Compartments.

    G. Section 10250 - Service Wall Units.

    H. Section 10260 - Wall and Corner Guards.

    I. Section 10750 - Telephone Specialties.

1.3 REFERENCES
NOTE ** Delete references from the list below that are not actually required by the text of the edited section.

    A. Americans with Disabilities Act Accessiblity Guidelines (ADAAG).

    B. ASTM A 240/A 240M - Standard Specification for Heat- Resisting Chromium and Chromium-Nickel Steel Plate, Sheet, and Strip for Pressure Vessels.

    C. ASTM A 554 - Standard Specification for Welded Stainless Steel Mechanical Tubing.

    D. ASTM C 1036 - Standard Specification for Flat Glass.

    E. ASTM F 446 - Standard Consumer Safety Specification for Grab bars and Accessories Installed in the Bathing Area.

1.4 SUBMITTALS

    A. Submit under provisions of Section 01300.

    B. Product Data: Manufacturer's product data for products specified, indicating selected options and accessories.

    C. Shop Drawings:

      1. Plans: Locate each specified unit in project.
      2. Elevations: Indicate mounting height of each specified unit in project.
      3. Details: Indicate anchoring and fastening details, required locations and types of anchors and reinforcement, and materials required for correct installation of specified products not supplied by manufacturer of products of this Section.

    D. Verification Samples: Two sample chips of each specified color and finish.

    E. Quality Assurance Submittals:

      1. Manufacturer's printed installation instructions for each specified product.
      2. Documentation of Manufacturer's Qualifications, specified in QUALITY ASSURANCE Article of this Section.

    F. Closeout Submittals: Warranty documents, issued and executed by manufacturer of products of this Section, and countersigned by Contractor.

1.5 QUALITY ASSURANCE

    A. Manufacturer Qualifications: Minimum five (5) years documented experience producing products specified in this Section.

     B. Regulatory Requirements: Conform to A.D.A. requirements.

 1.6 DELIVERY, STORAGE, AND HANDLING

    A. Factory-apply strippable protective vinyl coating to sight-exposed surfaces after finishing of products; ship products in manufacturer's standard protective packaging. 

    B. Storage and Protection: Store products in manufacturer's protective packaging until installation.

1.7 SEQUENCING

    A. Supply locating and sizing templates, and other requirements, to fabricators and installers of products referenced in RELATED SECTIONS Article for building-in products of this section. 

    B. Supply reinforcing and anchoring devices required for installation of products of this section to fabricators and installers of products referenced in RELATED SECTIONS Article. 

1.8 WARRANTY

    A. Manufacturer's standard warranty against defects in product workmanship and materials. 

    B. Manufacturer's 15-year warranty against silver spoilage of mirrors. 

PART 2 PRODUCTS

2.1 MANUFACTURERS

    A. Acceptable Manufacturers: ASI-American Specialties, Inc.; 441 Saw Mill River Road, Yonkers NY 10701-9986; Telephone (914) 476-9000, FAX (914) 476-0688.

NOTE ** Delete one of the two paragraphs below; coordinate with Division 01 requirements.

    B. Requests for substitutions will be considered in accordance with provisions of Section 01600. 

    C. Substitutions: Not permitted.

NOTE ** Delete paragraph below if substitutions not permitted. 

    D. Supply all products of this section from a single manufacturer.

2.2 MATERIALS

    A. Stainless Steel Sheet: ASTM A 240/A 240M, Type 304, 18-8 alloy.

NOTE ** Delete following paragraph if semi-recess mounting or surface-mounting of units designed for recessed mounting is not required.

    B. Cabinet Collars: Fabricated from 22 gage stainless steel sheet, finish matching cabinet finish; welded corners, finished to match sheet finish.

NOTE ** Following are descriptive specifications for the most commonly used accessories, plus "fill-in-the- blank" specifications for other types of accessories. Having the manufacturer's current catalog available for identification of options and model numbers will be essential for successful use of this section.

2.3 PROFILE SERIES 9000 CABINET-TYPE ACCESSORIES

NOTE ** The Profile Series is the only product of its type in the world to offer the strength, durability, and structural integrity that only 16 gage stainless steel doors can offer. No other unit is made with as heavy gage door as the ASI Profile Series.

    A. Basic Construction Requirements:

      1. Doors: Fabricated from single sheet 16 gage stainless steel, formed 15/16 inch return to wall, with vertical edges eased at 3/4 inch radius; welded corners, finished to match sheet finish.
      2. Cabinets: Fabricated from 18 gage stainless steel sheet, formed 1 inch wide flat perimeter trim four sides; all joints welded, sight-exposed welds finished to match sheet finish.
      3. Hinges: Stainless steel piano hinge, 3/16 inch diameter barrel, full length of cabinet; hinge leaves spot-welded to door and cabinet body.
      4. Locks: Flat rimless tumbler locks, keyed alike other toilet accessory locks, with two keys for each lock.
      5. Cabinet and Door Finish: No.4 satin stainless steel.

NOTE ** For each of this type of accessory, the following need to be identified:

NOTE ** - Accessory type and model number.

NOTE ** - Capacity, if optional.

NOTE **

NOTE ** If there is more than one of each functional type, copy the paragraph first and edit differently.

NOTE **

NOTE ** Delete the accessory types below that are not required.

    B. Paper Towel Dispenser TA-____: Model ______. 

    C. Paper Towel Dispenser and Disposal TA-____: Model ______. 

    D. Paper Towel Disposal TA-____: Model ______. 

    E. Sanitary Napkin Disposal TA-____: Model _____. 

    F. Multi-Purpose Unit TA-____: Model ______. 

    G. Dual Napkin/Tampon Vendor TA-____: Model ______. 

    H. Liquid Soap Dispenser TA-____: Model ______. 

    I. Toilet Seat Cover Dispenser TA-____: Model ______.

     J. Ash Tray TA-____: Model ______. 

2.4 SIMPLICITY LINE SERIES CABINET-TYPE ACCESSORIES

    A. Basic Construction Requirements:

    1. Doors: Fabricated from single sheet 18 gage stainless steel, formed 1/2 inch return to wall; welded corners, finished to match sheet finish.
    2. Cabinets: Fabricated from 22 gage stainless steel sheet, formed 1 inch wide flat perimeter trim four sides; all joints welded, sight-exposed welds finished to match sheet finish.
    3. Hinges: Stainless steel piano hinge, 3/16 inch diameter barrel, full length of cabinet; hinge leaves spot-welded to door and cabinet body.
    4. Locks: Tumbler locks, keyed alike other toilet accessory locks, with two keys for each lock.
    5. Cabinet and Door Finish: No.4 satin finish stainless steel.

NOTE ** For each of this type of accessory, the following need to be identified:

NOTE ** - Accessory type and model number.

NOTE ** - Mounting: Standard recessed mounting or surface- mounted with collar.

NOTE ** - Capacity, if optional.

NOTE **

NOTE ** If there is more than one of each functional type, copy the paragraph first and edit differently.

NOTE **

NOTE ** Delete the accessory types below that are not required. 

    B. Paper Towel Dispenser TA-____: Model ______. 

    C. Paper Towel Dispenser and Disposal TA-____: Model ______. 

    D. Paper Towel Disposal TA-____: Model ______. 

    E. Sanitary Napkin Disposal TA-____: Model _____. 

    F. Multi-Purpose Unit TA-____: Model ______. 

    G. Dual Napkin/Tampon Vendor TA-____: Model ______. 

    H. Liquid Soap Dispenser TA-____: Model ______. 

    I. Toilet Seat Cover Dispenser TA-____: Model ______.

    J. Ash Tray TA-____: Model ______. 

2.5 STANDARD LINE SERIES CABINET-TYPE ACCESSORIES

NOTE ** The Standard Series is the only one of its kind fabricated using a 1/4-inch thick "No-Flex" structural fiberboard core within the door, an exclusive ASI feature. The door is double pan construction of 22 gage stainless steel in which the "No-Flex" core is sandwiched. This gives the door greater structural integrity and makes it more dent resistant than other units. 

    A. Basic Construction Requirements:

      1. Doors: Fabricated from two sheets of 22 gage stainless steel, double pan construction, with 1/4 inch thick structural fiberboard core; welded corners, finished to match sheet finish.
      2. Cabinets: Fabricated from 22 gage stainless steel sheet, formed perimeter trim with 1/4 inch return to wall four sides; all joints welded, sight-exposed welds finished to match sheet finish.
      3. Hinges: Stainless steel piano hinge, 3/16 inch diameter barrel, full length of cabinet; hinge leaves spot-welded to door and cabinet body.
      4. Locks: Tumbler locks, keyed alike other toilet accessory locks, with two keys for each lock.
      5. Cabinet and Door Finish: No.4 satin finish stainless steel.

NOTE ** For each of this type of accessory, the following need to be identified:

NOTE ** - Accessory type and model number.

NOTE ** - Mounting: Standard recessed mounting or surface- mounted with collar.

NOTE ** - Capacity, if optional.

NOTE **

NOTE ** If there is more than one of each functional type, copy the paragraph first and edit differently.

NOTE **

NOTE ** Delete the accessory types below that are not required. 

    B. Paper Towel Dispenser TA-____: Model ______. 

    C. Paper Towel Dispenser and Disposal TA-____: Model ______. 

    D. Paper Towel Disposal TA-____: Model ______. 

    E. Sanitary Napkin Disposal TA-____: Model _____. 

    F. Multi-Purpose Unit TA-____: Model ______. 

    G. Dual Napkin/Tampon Vendor TA-____: Model ______. 

    H. Liquid Soap Dispenser TA-____: Model ______. 

    I. Toilet Seat Cover Dispenser TA-____: Model ______. 

    J. Ash Tray TA-____: Model ______. 

2.6 DESIGN LINE SERIES CABINET-TYPE ACCESSORIES

NOTE ** The Design Series is made using 1/2-inch thick solid phenolic doors, thicker than units of other manufacturers. In addition, the hinges are mortised into the door, rather than surface- mounted, using 1/4-inch long screws, providing a stronger bond between the door and the hinge. 

    A. Basic Construction Requirements:

      1. Doors: Fabricated from phenolic resin saturated Kraft core papers and face papers, bonded under heat and pressure phenolic resin saturated decorative face papers into solid sheet material, 1/2 inch thickness.
      2. Cabinets: Fabricated from 18 gage stainless steel sheet, formed 1 inch wide flat perimeter trim four sides; all joints welded, sight-exposed welds finished to match sheet finish.
      3. Hinges: Stainless steel piano hinge, 3/16 inch diameter barrel, full length of cabinet; hinge leaves spot-welded cabinet body, fastened to doors with stainless steel screws, 1/4 inch length.
      4. Locks: Tumbler locks, keyed alike other toilet accessory locks, with two keys for each lock.
      5. Cabinet Finish: No.4 satin finish stainless steel.
      6. Door Color(s): As selected by Architect from manufacturer's standard colors.
      7. Door Color(s): Indicated in Schedule Article of this section.
      8. Door Color: __________.

NOTE ** For each of this type of accessory, the following need to be identified:

NOTE ** - Accessory type and model number.

NOTE ** - Mounting: Standard recessed mounting or surface- mounted with collar.

NOTE ** - Capacity, if optional.

NOTE **

NOTE ** If there is more than one of each functional type, copy the paragraph first and edit differently.

NOTE **

NOTE ** Delete the accessory types below that are not required. 

    B. Paper Towel Dispenser TA-____: Model ______. 

    C. Paper Towel Dispenser and Disposal TA-____: Model ______. 

    D. Paper Towel Disposal TA-____: Model ______. 

    E. Sanitary Napkin Disposal TA-____: Model ______. 

    F. Multi-Purpose Unit TA-____: Model ______. 

    G. Dual Napkin/Tampon Vendor TA-____: Model ______. 

    H. Liquid Soap Dispenser TA-____: Model ______. 

    I. Toilet Seat Cover Dispenser TA-____: Model ______. 

    J. Ash Tray TA-____: Model ______.

2.7 TOILET ACCESSORIES

NOTE ** This Article covers accessories that do not fall into any of the Series listed above. 

    A. Basic Construction Requirements:

      1. Doors: Fabricated from minimum 22 gage stainless steel sheet, formed hems at sight-exposed edges; welded corners, finished to match sheet finish.
      2. Cabinets: Fabricated from minimum 22 gage stainless steel sheet, formed hems at sight-exposed edges; all joints welded, sight-exposed welds finished to match sheet finish.
      3. Hinges: Stainless steel piano hinge, 3/16 inch diameter barrel, full length of cabinet; hinge leaves spot-welded to door and cabinet body.
      4. Locks: Tumbler locks, keyed alike other toilet accessory locks, with two keys for each lock.
      5. Stainless Steel Finish: No.4 satin. 

    B. Soap Dispensers:

      1. Sight-exposed components: Stainless steel, minimum 22 gage.
      2. Internal components: Non-corroding chrome-plated brass, stainless steel, and ABS plastic.
      3. Locks: Tumbler locks, keyed alike other toilet accessory locks, with two keys for each lock.

NOTE ** For each of this type of accessory, the following need to be identified:

NOTE ** - Accessory type and model number.

NOTE ** - Mounting: Standard recessed mounting or surface- mounted with collar.

NOTE ** - Capacity, if optional.

NOTE **

NOTE ** If there is more than one of each functional type, copy the paragraph first and edit differently.

NOTE **

NOTE ** Delete the accessory types below that are not required. Add others not listed. 

    C. Paper Towel Dispenser TA-____: Model ______. 

    D. Paper Towel Dispenser and Disposal TA-____: Model ______. 

    E. Paper Towel Disposal TA-____: Model ______. 

    F. Sanitary Napkin Disposal TA-____: Model _____. 

    G. Multi-Purpose Unit TA-____: Model ______. 

    H. Dual Napkin/Tampon Vendor TA-____: Model ______. 

    I. Toilet Seat Cover Dispenser TA-____: Model ______. 

    J. Toilet Paper Holder TA-____: Model ______. 

    K. Combination Toilet Paper Holder/Seat Cover Dispenser TA- ____: Model ______. 

    L. Soap Dispenser TA-____: Model ______. 

    M. Utility Shelf TA-____: Model ______. 

    N. Baby Changing Station TA-____: Model ______. 

    O. Robe Hook TA-____: Model ______. 

    P. Heavy Duty Towel Hook TA-____: Model ______. 

    Q. Soap Dish TA-____: Model _______. 

    R. Shower Curtain Rod TA-____: Model ______. 

    S. Shower Curtain TA-____: Model ______, with Model ______ hooks. 

    T. Shower Seat TA-____: Model ______. 

    U. Medicine Cabinet TA-____: Model ______. 

    V. Mop Holder TA-____: Model ______. 

    W. Cup Dispenser TA-____: Model ______. 

2.8 MIRRORS

NOTE ** For each mirror type the following need to be defined:

NOTE ** - Frame type

NOTE ** - Mirror type - glass, plastic, or metal

NOTE ** - Mounting

NOTE ** - Shelf, optional

NOTE **

NOTE ** If more than one mirror type is required, copy the following paragraph and edit it differently for each type.

 A. Mirror TA-___: Model ________.

      1. Frame: Angle.
      2. Frame: Channel.
      3. Frame: Profile angle.
      4. Mirror: Plate glass.
      5. Mirror: Tempered glass.
      6. Mirror: Metal.
      7. Mirror: Polycarbonate (LexanJ).
      8. Mirror: Acrylic (Plexiglas7).
      9. Mirror: Laminated glass.

NOTE ** Delete the following paragraph if a shelf is not required.

      1. Shelf.
      2. Size: As indicated on drawings.
      3. Finish: No.4 satin stainless steel.

NOTE ** After identifying all the mirror types required, delete the descriptions below that are not applicable. 

    B. Angle Mirror Frames: Fabricated from 18 gage stainless steel, formed to 3/4 inch by 5/8 inch angle; heliarc- welded corners, finished to match sheet finish; concealed "H" type mounting bracket with tamper-proof fasteners. 

    C. Channel Mirror Frames: Fabricated from 20 gage stainless steel, formed to 1/2 inch by 1/2 inch by 1/2 inch channel; finished to match sheet finish; concealed mounting brackets with tamper-proof fasteners. 

    D. Profile Mirror Frames: Fabricated from 18 gage stainless steel, formed to 1 inch by 15/16 inch angle; vertical edges eased at 3/4 inch radius; heliarc-welded corners, finished to match sheet finish; concealed mounting bracket with tamper-proof fasteners. 

    E. Plate Glass Mirror: 1/4 inch thick polished plate glass, ASTM C 1036, Type I, Class 1, quality q1 mirror select; silver-coated, hermetically sealed with uniform electrolytically-deposited copper plating. 

    F. Tempered Glass Mirror: 1/4 inch thick polished tempered glass, two coats silver, hermetically sealed with uniform electrolytically-deposited copper plating, backpainted with waterproof coating. 

    G. Metal Mirror: Stainless steel, Type 304, No. 8 mirror finish. 

    H. Polycarbonate Mirror: 1/4 inch thick polycarbonate sheet ("Lexan"), silver-coated, sealed against silver spoilage. 

    I. Acrylic Mirror: 1/4 inch thick acrylic sheet ("Plexiglas"), silver-coated, sealed against silver spoilage. 

    J. Laminated Glass Mirror: Two sheets heat-treated 3/32 inch thick float glass laminated with 1/16 inch thick clear polyvinyl interlayer, two coats silver, hermetically sealed with uniform electrolytically- deposited copper plating, backpainted with waterproof coating. 

    K. Mirror Shelves: Fabricated from 18 gage stainless steel sheet, finish matching mirror frame, formed to 5 inches deep ledge with return and hemmed edges; spot-welded to mirror frame and gussets at corners, finished to match sheet finish. 

2.9 GRAB BARS

    A. Grab Bars - Basic Requirements: Fabricated to comply with ASTM F 446 and to withstand a 900 pound force, from ASTM A 554 stainless steel tubing, 18 gage, Type 304, 18- 8 alloy; formed 1-1/2 inch radius return to wall at each end; each end heliarc-welded to minimum 11 gage stainless steel circular flange; welds finished to match tube finish.

NOTE ** For grab bars, the Series defines whether it has concealed or exposed mounting and the diameter of the tube. 

    B. Grab Bars: Series _______.

      1. Peened finish.

NOTE ** Grab bars usually need to be detailed on the drawings, but if specifying a model number will be adequate, do so here.  

      1. Sizes and configurations: As indicated on drawings.
      2. Sizes and configurations: As indicated in Schedule at end of section.
      3. Grab Bar TA-____: Series ______, Type _____.

NOTE ** Delete the descriptions below that do not apply to the type of grab bars specified above. 

    C. Grab Bar Concealed Mounting Flanges: Stainless steel, 3 inch diameter by 1/2 inch deep, with 13 gage steel tenon plate for concealed attachment, using three set screws. 

    D. Grab Bar Snap-on Mounting Flanges: Snap-on stainless steel cover, 22 gage, 3 inch diameter by 1/2 inch deep, for concealing grab bar mounting flange. 

    E. Grab Bar Exposed Mounting Flange: Stainless steel, 1/8 inch thick, 3 inch diameter, with 3 countersunk screw holes. 

2.10 ELECTRICAL ACCESSORIESNOTE ** The following unit is "PorcelAir."

    A. Electric Hand Dryer TA-____: Model ______.

      1. Cast iron housing, single-piece construction, 1/4 inch thick, with acid-resistant porcelain enamel finish.
      2. Die-cast chrome-plated air nozzle with 360-degree rotation.
      3. Brushless electric motor rated 1/8 horsepower, 3200 revolutions per minute.

NOTE ** Delete one of the following paragraphs: 1700 watts is for hair dryer; 2300 watts is for hand dryer.  

      1. Heating element rated 1700 watts.
      2. Heating element rated 2300 watts.
      3. Fan capacity 153 cubic feet per minute.

NOTE ** The following unit is for Models 0110 through 0123. 

    B. Electric Hand Dryer TA-____: Model ______.

      1. Cast alloy housing, single-piece construction, with baked polyester coating.
      2. Die-cast chrome-plated air nozzle with 360-degree rotation.
      3. Brushless electric motor rated 1/8 horsepower, 3000 revolutions per minute.
      4. Heating element rated 2300 watts.
      5. Fan capacity 180 cubic feet per minute.

NOTE ** The following unit is Magna Max Model Numbers 0130- 0132. 

    C. Electric Hand Dryer TA-____: Model ______.

      1. Formed polycarbonate housing, white color, single- piece construction; integral recessed air nozzle.
      2. Integral intake grille recirculates heated air. 

2.11 HOSPITAL AND MEDICAL SERVICE ACCESSORIES

    A. Modular Lavatory Station TA-____: Model _____.

      1. Doors: Fabricated from 22 gage stainless steel sheet, with 1/4 inch returns and hemmed edges.
      2. Cabinet: Fabricated from 22 gage stainless steel sheet, formed 1 inch wide perimeter trim with 1/4 inch return to wall, four sides; all joints welded, sight-exposed welds finished to match sheet finish.
      3. Apron: Fabricated from 18 gage stainless steel sheet, fitted with faucet, handles, and fittings.
      4. Hinges: Stainless steel piano hinge, 3/16 inch diameter barrel, full length of cabinet; hinge leaves spot-welded to door and cabinet body. 

    B. Corner Guards TA-____: Model ______; fabricated from 18 gage stainless steel, radiused corner. 

    C. Recessed Surgical Glove Dispenser TA-____: Model ______; fabricated from 22 gage stainless steel sheet. 

    D. Recessed Bedpan and Urinal Cabinet TA-____: Model _____.

      1. Door: Fabricated from 22 gage stainless steel sheet, with 1/4 inch returns and hemmed edges; welded corners, finished to match sheet finish.
      2. 2. Airspace: 1/2 inch, continuous, above and below door.
      3. Cabinet: Fabricated from 22 gage stainless steel sheet, formed 1 inch wide perimeter trim with 1/4 inch return to wall, four sides; all joints welded, sight-exposed welds finished to match sheet finish.
      4. Hinges: Stainless steel piano hinge, 3/16 inch diameter barrel, full length of cabinet; hinge leaves spot-welded to door and cabinet body. 

    E. Pass Through Specimen Cabinet TA-____: Model _____.

      1. Self-closing Doors: Fabricated from 22 gage stainless steel sheet, with 1/4 inch returns and hemmed edges; welded corners, finished to match sheet finish; interlock on doors prevents both doors from being opened at the same time.
      2. Cabinet: Fabricated from 22 gage stainless steel sheet, formed 1 inch wide perimeter trim with 1/4 inch return to wall, four sides; all joints welded, sight-exposed welds finished to match sheet finish; adjustable for wall thickness 1-3/4 inches to 5-1/2 inches.
      3. Hinges: Stainless steel piano hinge, 3/16 inch diameter barrel, full length of cabinet; hinge leaves spot-welded to door and cabinet body.
      4. Removable Tray: Fabricated from 22 gage stainless steel sheet. 

    F. Turntable Specimen Pass Cabinet TA-____: Model ______.

      1. Turntable Cylinder Assembly: Fabricated from 18 gage stainless steel sheet, 12 inches diameter, with 10- 1/2 inch by 6 inch opening; removable cylinder housing with lock; welded corners, finished to match sheet finish.
      2. Cabinet Trim: Fabricated from 22 gage stainless steel sheet, formed 1 inch wide perimeter trim with 1/4 inch return to wall, four sides; all joints welded, sight-exposed welds finished to match sheet finish; adjustable for wall thickness 3 inches to 7 inches.
      3. Main Body: Self-lubricating ball bearing plate mounted on top and bottom permitting unit to revolve freely; positioned bullet catch prevents uncontrolled rotation. 

PART 3 EXECUTION

3.1 EXAMINATION

    A. Verification of Conditions:

      1. Prepared openings are sized and located in accordance with shop drawings.
      2. Reinforcement and anchoring devices are correct type and are located in accordance with shop drawings. 

    B. Installer's Examination:

  1. Have installer of this section examine conditions under which construction activities of this section are to be performed, then submit written notification if such conditions are unacceptable.
  2. Transmit two copies of installer's report to Architect within 24 hr of receipt.
  3. Beginning construction activities of this section before unacceptable conditions have been corrected is prohibited.
  4. Beginning construction activities of this section indicates installer's acceptance of conditions. 

3.2 INSTALLATION

    A. Install toilet accessories plumb and level in accordance with shop drawings and manufacturer's printed installation instructions. 

    B. Locate toilet accessories at heights specified by Americans with Disabilities Act. 

3.3 CLEANING

    A. Remove manufacturer's protective vinyl coating from sight- exposed surfaces 24 hours before final inspection. 

    B. Clean surfaces in accordance with manufacturer's recommendations.

 

3.4 PROTECTION OF INSTALLED PRODUCTS

    A. Protect products from damage caused by subsequent construction activities. 

    B. Field repair of damaged product finishes is prohibited; replace products having damaged finishes caused by subsequent construction activities.

 

3.5 SCHEDULE

NOTE ** If accessories are not located on a drawing in either plan or elevation, a schedule may be used to identify types and quantities for each room or area. Such a schedule can also be used to identify different colors for colored finishes.

NOTE **

NOTE ** Use the TA-numbers established above to simplify the schedule -- repetition of specification requirements in the schedule introduces the potential for conflicting or contradictory requirements.

NOTE **

NOTE ** The areas can be identified generally by type, such as "men's toilet rooms," or exactly by room number.

NOTE **

NOTE ** Following are some samples of specific room types to use in preparation of a schedule for the project.

NOTE ** For best results, prepare the schedule first, identifying each different accessory by TA-number and making a note of the model number that applies.

Then go back to the specification above and delete all items and descriptive specifications that do not apply. Where there is more than one variety of a particular functional type of accessory, such as 2 styles of mirrors, edit the type descriptions to show what each type is and give each the unique TA- number that corresponds to the schedule. 

    A. Men's Public Washrooms:

      1. Mirror TA-____, at each lavatory except handicapped.
      2. Mirror TA-____, at handicapped lavatory.
      3. Soap Dispenser TA-____, at each lavatory.
      4. Paper Towel Dispenser/Disposal TA-____.
      5. Toilet Tissue Dispenser/Seat Cover Dispenser TA-____, at each pair of compartments with common partition (back-to-back mounting).
      6. Toilet Tissue Dispenser TA-____, at each other compartment.
      7. Seat Cover Dispenser TA-____, at each other compartment.
      8. Grab Bars TA-____, at handicapped stall; configuration as indicated on drawings. 

    B. Women's Public Washrooms:

      1. Mirror TA-____, at each lavatory except handicapped.
      2. Mirror TA-____, at handicapped lavatory.
      3. Soap Dispenser TA-____, at each lavatory.
      4. Paper Towel Dispenser/Disposal TA-____.
      5. Toilet Tissue Dispenser/Napkin Disposal TA-____, at each pair of compartments with common partition (back- to-back mounting).
      6. Seat Cover Dispenser TA-____, at compartments with back-to-back units above.
      7. Toilet Tissue Dispenser/Seat Cover Dispenser/Napkin Disposal TA-____, at each other compartment.
      8. Grab Bars TA-____; configuration as indicated on drawings.
      9. Napkin/Tampon Vendor TA-____.
      10. Double Robe Hook TA-____, adjacent to baby changing station.
      11. Baby Changing Station TA-____. 

    C. School Locker Room (Boys):

      1. Mirror TA-____, at each lavatory except handicapped.
      2. Mirror TA-____, at handicapped lavatory.
      3. Soap Dispenser TA-____.
      4. Electric Hand Dryer TA-____.
      5. Toilet Tissue Dispenser TA-____, at each pair of compartments with common partition (back-to-back mounting).
      6. Toilet Tissue Dispenser TA-____, at each other compartment.
      7. Grab Bars TA-____; configuration as indicated on drawings.
      8. Shower Curtain Rod/Hooks/Shower Curtain TA-____.
      9. Heavy Duty Towel Hook TA-_____. 

    D. Hospital Patient Bathroom:

      1. Mirror TA-____.
      2. Soap Dispenser TA-____.
      3. Paper Towel Dispenser TA-____.
      4. Paper Towel Disposal TA-____.
      5. Toilet Tissue Dispenser TA-____.
      6. Cup Dispenser TA-____.
      7. Grab Bars TA-____; configuration as indicated on drawings.
      8. Shower Curtain Rod/Hooks/Shower Curtain TA-____.
      9. Shower Seat TA-____.
      10. Robe Hook TA-_____.
      11. Bed Pan/Urinal Cabinet TA-____. 

    E. Hospital Exam Room:

      1. Modular Lavatory Station TA-____.
      2. Waste Receptacle TA-____.
      3. Surgical Glove Dispenser TA-____.
      4. Specimen Pass-Thru Box TA-____.
      5. Double Robe Hook TA-____. 

    F. Inmate Prison Cell: All accessories rear-mounted, verify wall depths.

NOTE ** The following accessories should be chosen for detention use and would not be the same accessories used in non-security locations.

      1. Metal Mirror TA-____.
      2. Soap Dish TA-____.
      3. Toilet Tissue Holder TA-____.
      4. Shelf TA-____.
      5. Detention Clothes Hook TA-____. 

    G. Janitor's Closet:

      1. Utility Shelf/Mop Holder TA-____; length _____.
      2. Pail or Ladder Hook TA-____. 

END OF SECTION

Send Enquiry